You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.
Home > Cellular Security > SecureGuard Hidden Cameras with B-Link OnBoard User Guide
SecureGuard Hidden Cameras with B-Link OnBoard User Guide
print icon

Getting Started:

Your SecureGuard 4G Hidden Camera is very simple to set up and use. Follow the instructions below to get started.

Using the included cables, insert the micro USB into the devices. It is recommended that both the B-Link Secure 4G Camera connector and power bank are charged for up to 6 hours or until fully charged. Once the devices are fully charged, remove the cables and power the devices on.

The battery will show the battery percentage on the upper right-hand corner of the B-Link Secure 4G Camera connector. On the left corner side, you will see the AT&T 4G connection and signal strength. All indicator lights will Illuminate blue on the power bank when fully charged.


Camera Set-Up

For the 4G B-Link Secure Cellular WiFi connector: (Turn on 1st) 

1. Fully charge the 4G WiFi connector and the modem’s power bank. Turn on the 4G WiFi connector and power bank. Connect the power bank to the modem. Give the 4G WiFi connector up to 90 seconds for it to initialize. Pay attention to the front display before deploying the unit in the field. The WiFi connector will display the 4G AT&T network connection. 

Power​: It’s highly recommended that the battery icon in the top right corner is full (4 bars).

Wi-Fi​: The second icon from the right shows connected devices. “(1)” shows that the camera is connected. If “(0)” displays, that means the camera is not connected. 

4G​: The screen should display “4G” to represent the connection to AT&T’s 4G network. If “4G” is not displayed. Try to reboot the modem or move to a different area. 

Signal: The icon on the top left corner shows cell network signal strength. For an excellent connection, you must receive 4+ bars. 2 bars of less represent a weak connection, The camera should still connect but may be slow or may have a major time lag. 

 

For the camera Module: (Turn on 2nd) 

1. For best results, always make sure the battery is full. 

2. Connect the USB power cable between the power bank and the camera. 

3. Watch for a status near the edge of the camera module. This camera lights should blink when you connect the power. The lights will turn off when the camera is finished initializing. Give the camera up to 5 minutes to fully initialize. 

 

PC​ ​Connection​ ​(CloudSEE)

Data​ ​Usage:​ ​The​ ​4G​ ​hidden​ ​camera​ ​will​ ​use​ ​about​ ​5MB/minute​ ​for​ ​the​ ​internet​ ​video stream.​ ​A 1GB​ ​data ​plan​ ​may​ ​give​ ​you​ ​about​ ​250​ ​minutes​ ​of​ ​live​ ​viewing​ ​time. 

1. Install the JSetup_EN.exe software on CD provided. 
2. After the software finishes installing open the CloudSEE icon on your desktop. 
3. You will be prompt to enter an ID and PW. Enter ID: ABC PW: 123__ 
4. Click on Setting, go to CloudSee ID and enter ___B400977343__
5. Username: Admin__ Password: 123__ Click OK.
6. Your screen might be divided into 4 to connect 4 cameras. Click the large square near the bottom to change the screen division 1. 
7. Click Link All.
8. Now you should be able to watch your camera live.
9. You will be able to watch your camera live from anywhere in the world.

iPhone​ ​/​ ​Android​ ​Connection​ ​(NVSIP)

Data​ ​Usage:​ ​The​ ​4G​ ​hidden​ ​camera​ ​will​ ​use​ ​about​ ​5MB/minute​ ​for​ ​the​ ​internet​ ​video stream.​ ​A 1GB​ ​data​ ​plan​ ​may​ ​give​ ​you​ ​about​ ​250​ ​minutes​ ​of​ ​live​ ​viewing​ ​time.

  1. Download NVSIP​.
  2. Open NVSIP​, Register an account or access through Visitor​ ​Login​. 
  3. Press the (+)​ icon, Type B400977343​ ​ in the Please​ ​input​ ​Device​ ​ID​field.
  4. CH Amount: Enter 1​
  5. Username:​ ​Enter ​Admin​, ​PW:​ 123
  6. Click Add​.

 


Please see below for the complete User Guide.

Feedback
3 out of 3 found this helpful

scroll to top icon